• Text Size
  • S
  • M
  • L
  • TOP > A brand

Search

Keyword or Sentence(200characters) 
(example)
Search for both A and B : A (space) B
Search for either A or B : A|B
Search for A excluding B : A-B

Category: A brand

Results:127 ,Showing: 21 - 30

≪ 3 / 13Page ≫

  • Dry processing in A Tap

    Dry processing at A Tap It is okay to use non-water-soluble coolant and water-soluble emulsion type, but we do not recommend water-soluble coolant with poor... 詳細表示

    • No：17835
    • Publication Date：2025/09/05 11:11
    • Updated Date：2025/10/17 17:30
    • Category： A-Tap

  • What is AE-MSS-H?

    What is AE-MSS-H? Carbide end mill for high-hardness steel multiple flutes Square type stub type (= shorter than short type flute length = 1.5D). ▲ T... 詳細表示

    • No：18085
    • Publication Date：2025/09/05 11:11
    • Updated Date：2026/01/16 15:32
    • Category： A end mill

  • What is an end mill that can process ...

    If there is an indication for a right-angle corner in the drawing, the end mill side must also be at a right angle. However, in the case of a typical carbide... 詳細表示

    • No：18036
    • Publication Date：2025/09/05 11:11
    • Updated Date：2025/10/22 14:42
    • Category： A end mill

  • If the ADF flat drill has high rigidi...

    The high rigidity of the ADF is due to its shallow 20‑degree spiral flute. The unique flute geometry and smoothing process provide both excellent chip evacu... 詳細表示

    • No：17912
    • Publication Date：2025/09/05 11:11
    • Updated Date：2026/01/14 16:02
    • Category： A drill

  • What are the benefits of S-XPF torque...

    XPF, which has low torque and low heat generation, can be used for rolling large-diameter, high-hardness materials. It is also effective for high-speed, lon... 詳細表示

    • No：17820
    • Publication Date：2025/09/05 11:11
    • Updated Date：2025/11/18 15:22
    • Category： A-Tap

  • When using AE-VTSS for plunge cutting...

    Since this end mill has a relief angle, plunge cutting alone will not produce a flat bottom surface. However, if you follow up with lateral cutting or simil... 詳細表示

    • No：18162
    • Publication Date：2025/09/05 11:11
    • Updated Date：2025/12/08 16:02
    • Category： A end mill

  • Can AT-2 be reground？

    AT-2 cannot be reground. 詳細表示

    • No：18032
    • Publication Date：2025/09/05 11:11
    • Updated Date：2025/12/08 16:49
    • Category： A-thread mill

  • Can The ADO-SUS drill series be regr...

    The ADO-SUS drill series can be reground . Recoating is also recommended for better performance. However, since we also use our own cutting edge specificati... 詳細表示

    • No：17896
    • Publication Date：2025/09/05 11:11
    • Updated Date：2025/12/11 17:01
    • Category： A drill

  • Is it possible to support deep hole d...

    Is it possible to support deep hole drilling with A-SFT? The A-SFT supports effective thread depths up to 2.5D (2.5 times the outer diameter of the thread).... 詳細表示

    • No：17853
    • Publication Date：2025/09/05 11:11
    • Updated Date：2025/09/16 15:15
    • Category： A-Tap

  • What is AE-ML-H?

    It is an end mill that is ideal for reducing cycle time for side milling with high hardness steel. What is AE-ML-H? Carbide end mill for high-hardness ... 詳細表示

    • No：18136
    • Publication Date：2025/09/05 11:11
    • Updated Date：2026/01/16 15:41
    • Category： A end mill

Results:127 ,Showing: 21 - 30

TOP