• Text Size
  • S
  • M
  • L
  • TOP > A brand

Search

Keyword or Sentence(200characters) 
(example)
Search for both A and B : A (space) B
Search for either A or B : A|B
Search for A excluding B : A-B

Category: A brand

Results:127 ,Showing: 11 - 20

≪ 2 / 13Page ≫

  • What is an end mill that can process ...

    If there is an indication for a right-angle corner in the drawing, the end mill side must also be at a right angle. However, in the case of a typical carbide... 詳細表示

    • No：18036
    • Publication Date：2025/09/05 11:11
    • Updated Date：2025/10/22 14:42
    • Category： A end mill

  • What is the sharp corner edge for ADF...

    It will be the sharp corner edge. It is a specification that allows you to aim for a right-angle shape at the bottom of the hole. * The ADF and ADFO ... 詳細表示

    • No：17972
    • Publication Date：2025/09/05 11:11
    • Updated Date：2025/11/11 17:04
    • Category： A drill

  • Difference from A Tap and VP-SFT

    A-SFT is recommended up to 30HRC. VP-SFT is recommended for harder materials (30~42HRC). References: A Tap Series 詳細表示

    • No：17844
    • Publication Date：2025/09/05 11:11
    • Updated Date：2026/01/23 14:55
    • Category： A-Tap

  • What is ADFO, a flat drill with carbi...

    What is ADFO, a flat drill with carbide oil holes? Compatible with stainless steel, the flat drill that can process up to 3 times the diameter of the tool i... 詳細表示

    • No：17984
    • Publication Date：2025/09/05 11:11
    • Updated Date：2025/11/07 15:46
    • Category： A drill

  • What should I do when machining titan...

    When machining titanium alloys, if bellows-shaped chips are produced, this phenomenon is likely caused by cutting conditions being too fast. Reduce the cutt... 詳細表示

    • No：17901
    • Publication Date：2025/09/05 11:11
    • Updated Date：2025/11/13 16:39
    • Category： A drill

  • Is it possible to use non-water-solub...

    Is it possible to use non-water-soluble coolant (internal coolant) in ADO-SUS drills? Compared to water-soluble coolant, the cooling effect and oil discharg... 詳細表示

    • No：17897
    • Publication Date：2025/09/05 11:11
    • Updated Date：2026/01/15 10:21
    • Category： A drill

  • Is it possible to support deep hole d...

    Is it possible to support deep hole drilling with A-SFT? The A-SFT supports effective thread depths up to 2.5D (2.5 times the outer diameter of the thread).... 詳細表示

    • No：17853
    • Publication Date：2025/09/05 11:11
    • Updated Date：2025/09/16 15:15
    • Category： A-Tap

  • I would like to know whether AE-VTFE-...

    Regrinding is possible. To ensure performance, recoating is also recommended. If you are considering regriding or recoating, please contact the OSG sales... 詳細表示

    • No：18142
    • Publication Date：2025/09/05 11:11
    • Updated Date：2025/12/05 13:27
    • Category： A end mill

  • Can AE-MSS-H be reground?

    AE-MSS-H can be reground . In order to ensure performance, recoating is also recommended. If you are considering recoating and regrinding, please con... 詳細表示

    • No：18086
    • Publication Date：2025/09/05 11:11
    • Updated Date：2025/12/11 16:53
    • Category： A end mill

  • The oil hole shape of the ADO-SUS dri...

    It is a new type of oil hole called MEGA COOLER. Compared to the general specifications, it has a discharge rate of more than 30%, and is highly effective in... 詳細表示

    • No：17899
    • Publication Date：2025/09/05 11:11
    • Updated Date：2025/09/18 15:58
    • Category： A drill

Results:127 ,Showing: 11 - 20

TOP